Differential Gear Ratio Chart: Ratios, RPM & Speed Compared

On this page, differential gear ratio chart is the case in point: A differential gear ratio chart puts the common axle ratios side by side so the trade between them can be seen at a glance: the RPM at a given speed, the speed at a given RPM, and how far each ratio moves the engine speed. This page is that chart, built from the formula RPM = (speed × gear ratio × final drive × 336) ÷ tyre diameter in inches, with the assumptions stated next to every table so the numbers can be reworked for a different tyre size. The tables assume 28-inch tyres (example diameter) and a 1:1 top gear unless stated otherwise, and the sections after the tables explain what the numbers mean for acceleration, cruising, towing and fuel use, and how to read the chart for a vehicle with different tyres.

Taking differential gear ratio chart as the case in point: The chart covers the ratios most often fitted to cars and light trucks, from tall cruising ratios around 3.07 to short ratios around 4.10 and beyond, and the RPM table shows all of them at 30, 50 and 70 mph so the spread is visible in one place. A 3.07 and a 4.10 differ by about a third in engine speed at any road speed, which is why the choice matters as much as it does — and why it should be made from the table with the actual tyre diameter rather than from the ratio number alone. The worked example below shows the arithmetic for one ratio so any line of the chart can be verified by hand.

This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.

How the gear ratio formula works for differential gear ratio chart

For differential gear ratio chart, the point is this: Two formulas do the work, and both are worth knowing because they let any gear-ratio result be checked by hand. Engine speed is RPM = (speed × gear ratio × final drive × 336) ÷ tyre diameter in inches, where speed is in miles per hour and the tyre diameter is the nominal new-tyre diameter. Road speed is the same relationship rearranged: speed = (RPM × tyre diameter) ÷ (gear ratio × final drive × 336). The 336 is a unit-conversion constant, not a measured quantity, so it never changes. In a 1:1 top gear the gear ratio drops out and RPM depends only on speed, the axle ratio and the tyre diameter — which is why a ratio change or a tyre change shows up immediately as a different cruising RPM. Work through the formula once with your own numbers and the tables below stop being something to take on trust.

What a gear ratio is for differential gear ratio chart

Taking differential gear ratio chart as the case in point: The axle ratio is the final multiplication in the driveline. The engine's torque passes through the gearbox, where each gear multiplies it by its own ratio, then through the differential, where the ring and pinion multiply it once more. A 3.73 ratio multiplies the torque arriving at the differential by 3.73 before it reaches the wheels, while a 4.10 multiplies it by 4.10. That extra multiplication is why a numerically higher ratio feels stronger off the line and holds speed better on a grade with a trailer behind it. The trade is engine speed: at the same road speed and in the same gearbox gear, the higher ratio turns the engine faster, which is why cruising RPM rises when a shorter ratio is fitted. The ratio itself is set by the tooth counts of the ring gear and pinion, so it is a physical fact about the axle rather than a setting that can be adjusted from the driver's seat.

differential gear ratio chart: Worked example: RPM at 30, 50 and 70 mph

For differential gear ratio chart, the point is this: Take a 3.73 axle ratio on 28-inch tyres (example diameter), in top gear at 1.00. At 70 mph the formula gives RPM = (70 × 1.00 × 3.73 × 336) ÷ 28 = 3,133 RPM. At 50 mph it gives 2,238 RPM and at 30 mph 1,343 RPM. The speed at 2,000 RPM is 44.7 mph and at 3,000 RPM it is 67.0 mph. With a 3.07 ratio the 70 mph figure falls to 2,579 RPM, and with a 4.10 it rises to 3,444 RPM — the full spread is in the table below, and every line of it comes from the same formula with the same stated assumption.

RPM table: 3.07, 3.55 and 4.10 at 30, 50 and 70 mph for differential gear ratio chart

Taking differential gear ratio chart as the case in point: Assumption: 28-inch tyres (example diameter), top gear 1.00. RPM = (speed × ratio × 336) ÷ 28.

Speed 3.07 ratio 3.55 ratio 3.73 ratio 4.10 ratio
30 mph 1,105 RPM 1,278 RPM 1,343 RPM 1,476 RPM
50 mph 1,842 RPM 2,130 RPM 2,238 RPM 2,460 RPM
70 mph 2,579 RPM 2,982 RPM 3,133 RPM 3,444 RPM

For differential gear ratio chart, the point is this: The table makes the trade concrete. At 70 mph the 3.07 cruises at the lowest RPM and the 4.10 at the highest, with a gap of about a third between them, and the same gap appears at 30 and 50 mph because the ratio multiplies the RPM at every speed. A taller ratio suits a vehicle that spends its life cruising; a shorter ratio suits one that tows, climbs or runs bigger tyres. The middle ratios are the compromise, and the worked example above shows how to rework any line of the table for a different tyre diameter: divide the table's RPM by the old diameter and multiply by the new one, or run the formula again from the start.

differential gear ratio chart: How tyre diameter changes the answer

Taking differential gear ratio chart as the case in point: The tyre diameter belongs in the formula because it sets how far the vehicle moves per wheel revolution. A 35-inch tyre travels about 110 inches per turn while a 31-inch tyre travels about 97 inches, so the same driveshaft speed moves the bigger-tyre vehicle further and the engine turns more slowly at a given road speed. That is why a ratio that felt right on the original tyres can feel sluggish after a lift and bigger tyres: nothing about the engine changed, but the effective gearing grew taller by the same percentage as the diameter. The fix is a numerically higher ratio that brings the RPM back to where it was. All diameters quoted here are nominal new-tyre figures computed from the size code, and real tyres vary slightly by brand, model, wear and inflation pressure.

differential gear ratio chart: What the ratio does on the road

On this page, differential gear ratio chart is the case in point: What a ratio change feels like depends on the direction. A shorter ratio — a higher number — raises engine speed at every road speed, sharpens throttle response, makes towing on grades easier and brings the engine into its power band sooner after each gearchange. The price is paid on the motorway: higher cruising RPM, more engine noise and, usually, more fuel used at a steady cruise. A taller ratio — a lower number — does the reverse: quieter, lower-RPM cruising and less fuel at steady speed, at the cost of lazier acceleration and more downshifting on hills or with a load. Neither direction is free, which is why the choice is a compromise between the vehicle's hardest job and its most common one, and why the tables below show the RPM for several ratios side by side instead of recommending one.

How to find the ratio already fitted for differential gear ratio chart

On this page, differential gear ratio chart is the case in point: Finding the ratio already fitted is a matter of looking in the right places. The axle tag, usually a small metal tag bolted to the differential cover, often stamps the ratio directly. The door-jamb placard and the owner's manual list the axle and tyre specification for the vehicle as built, and the build sheet or window sticker carries the same information in coded form. A VIN decoder can also return the original axle ratio, though it reports the vehicle as built rather than as it stands now, so it will not catch a previous owner's axle swap. The hands-on check is to count teeth: mark the ring gear and pinion, count the teeth on each, and divide ring teeth by pinion teeth — 41 ring teeth and 11 pinion teeth give 41 ÷ 11 = 3.73. If the tag, the paperwork and the tooth count disagree, the tooth count is the one to trust, because it describes the axle actually fitted.

Common mistakes with gear ratios for differential gear ratio chart

Mistakes usually come from using half the formula. The first is to pick a ratio from a chart without entering the actual tyre diameter — the chart's assumption may be a different size from the tyres on the vehicle, and the answer follows the assumption, not the vehicle. The second is to forget that the gearbox gear matters: first gear multiplies torque far more than top gear, so a crawl or launch question needs the first-gear ratio while a cruising question needs top gear. The third is to read a higher ratio as simply better: it raises cruising RPM, which can raise noise and fuel use on long motorway runs, so the gain in acceleration is paid for at cruising speed. The fourth is to trust a ratio stamped on an axle tag without checking that the axle is original to the vehicle — a swapped axle carries its own ratio. And the fifth is to treat the calculation as permission: the maths says what the RPM will be, not that the change is suitable, so a drivetrain specialist should confirm the choice before parts are ordered. That is the point this page works through for differential gear ratio chart.

differential gear ratio chart: Related pages

Frequently asked questions

How do I work out the RPM for differential gear ratio chart?

For differential gear ratio chart, the point is this: Use RPM = (speed × gear ratio × final drive × 336) ÷ tyre diameter in inches, with the gear in use and the axle ratio for the vehicle. The worked example above shows the arithmetic at 30, 50 and 70 mph with the assumptions stated, and the gear ratio calculator runs the same formula with your own numbers.

What does a higher gear ratio do?

A numerically higher ratio — a shorter gear — raises engine speed at every road speed, multiplies torque more at the wheels, sharpens acceleration and helps towing, at the cost of higher cruising RPM and usually more fuel on steady motorway runs. A lower number does the opposite. The table above shows the RPM for several ratios side by side so the trade is visible. That is the point this page works through for differential gear ratio chart.

How does tyre size affect gear ratio?

For differential gear ratio chart, the point is this: A larger tyre diameter makes the effective gearing taller: the vehicle travels further per wheel revolution, so the engine turns more slowly at a given road speed. A 10% larger diameter cuts cruising RPM by roughly 9% with the same ratio. That is why bigger tyres are usually paired with a numerically higher ratio, to restore the RPM the vehicle had before the tyre change.

Does changing the gear ratio affect the speedometer?

Taking differential gear ratio chart as the case in point: Yes, indirectly: the speedometer is calibrated for a rolling circumference, and a ratio change does not change the tyre, so the speedometer reading itself is unaffected by the ratio alone. What changes is the engine speed at a given road speed. A tyre-size change does affect the speedometer, because it changes the rolling circumference — see the speedometer error calculator for that calculation.

Can I change my gear ratio myself?

Taking differential gear ratio chart as the case in point: A ratio change means replacing the ring gear and pinion and setting the backlash and preload precisely, which is a specialist drivetrain job with special tools. An incorrect setup fails quickly and expensively. Most owners have the work done by a drivetrain specialist, who can also confirm the ratio suits the axle, the gearbox and the way the vehicle is used.