3.31 Gear Ratio: RPM, Speed & What 3.31 Means on the Road

On this page, 3.31 gear ratio is the case in point: A 3.31 gear ratio means the driveshaft turns 3.31 times for every single turn of the wheels, and that one number sets the engine speed at every road speed. In top gear, where the gearbox ratio is 1.00, the engine speed follows directly from the ratio and the tyre diameter: a 3.31 ratio on 205/55R16 tyres (631.9 mm, 24.88 in) puts the engine at a very specific RPM at 30, 50 and 70 mph, and this page works those numbers out line by line so the result can be checked by hand. The tables below use the formula RPM = (speed × gear ratio × final drive × 336) ÷ tyre diameter in inches, with the assumptions stated next to each table, and the rest of the page explains what the ratio does to acceleration, cruising, towing and fuel use — and what it does not do.

The short version is that 3.31 sits in the middle of the ratios commonly fitted to cars and light trucks: shorter than a 3.21, taller than a 4.10, and a compromise between pulling power and quiet cruising. Whether it is the right ratio for a particular vehicle depends on the tyre diameter, the weight being moved and how the vehicle is used, so the worked example below uses 205/55R16 tyres (631.9 mm, 24.88 in) and shows the RPM at the speeds that matter, and a comparison table puts 3.31 next to 3.07, 3.55 and 4.10 so the difference is visible rather than guessed. Every figure is a calculation from the stated inputs, and the disclaimer below applies to all of it. That is the point this page works through for 3.31 gear ratio.

This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.

How the gear ratio formula works for 3.31 gear ratio

For 3.31 gear ratio, the point is this: The formula that ties speed, ratio and tyre size together is RPM = (speed × gear ratio × final drive × 336) ÷ tyre diameter in inches. Speed is in miles per hour, gear ratio is the gearbox gear in use, final drive is the axle ratio, and 336 is the constant that converts miles, hours and inches into revolutions per minute. In top gear on most gearboxes the gear ratio is 1.00, so the formula simplifies to RPM = (speed × final drive × 336) ÷ tyre diameter. Turn it around and it gives speed from RPM: speed = (RPM × tyre diameter) ÷ (gear ratio × final drive × 336). Both directions use the same numbers, so a table built from one can be checked from the other, and any result can be verified by hand with a pocket calculator. The tyre diameter used here is the nominal new-tyre figure; real tyres vary slightly by brand, model, wear and inflation pressure.

3.31 gear ratio: What a gear ratio is

The axle ratio is the final multiplication in the driveline. The engine's torque passes through the gearbox, where each gear multiplies it by its own ratio, then through the differential, where the ring and pinion multiply it once more. A 3.73 ratio multiplies the torque arriving at the differential by 3.73 before it reaches the wheels, while a 4.10 multiplies it by 4.10. That extra multiplication is why a numerically higher ratio feels stronger off the line and holds speed better on a grade with a trailer behind it. The trade is engine speed: at the same road speed and in the same gearbox gear, the higher ratio turns the engine faster, which is why cruising RPM rises when a shorter ratio is fitted. The ratio itself is set by the tooth counts of the ring gear and pinion, so it is a physical fact about the axle rather than a setting that can be adjusted from the driver's seat. That is the point this page works through for 3.31 gear ratio.

3.31 gear ratio: Worked example: 3.31 ratio at 30, 50 and 70 mph

Taking 3.31 gear ratio as the case in point: Take a 3.31 axle ratio on 205/55R16 tyres (631.9 mm, 24.88 in), in top gear at 1.00. At 70 mph the formula gives RPM = (70 × 1.00 × 3.31 × 336) ÷ 24.88 = 3,129 RPM. At 50 mph the same calculation gives RPM = (50 × 1.00 × 3.31 × 336) ÷ 24.88 = 2,235 RPM, and at 30 mph it gives 1,341 RPM. The speed at 2,000 RPM is (2,000 × 24.88) ÷ (1.00 × 3.31 × 336) = 44.7 mph, and at 3,000 RPM it is 67.1 mph. Each of those numbers can be re-checked with the formula above, and changing the tyre diameter changes all of them in proportion — a 10% larger diameter cuts every RPM figure by roughly 9%.

3.31 gear ratio: RPM table: 3.31 against 3.07, 3.55 and 4.10

For 3.31 gear ratio, the point is this: Assumption: 205/55R16 tyres (631.9 mm, 24.88 in), top gear 1.00. RPM = (speed × ratio × 336) ÷ 24.88.

Speed 3.07 ratio 3.31 ratio 3.55 ratio 4.10 ratio
30 mph 1,244 RPM 1,341 RPM 1,438 RPM 1,661 RPM
50 mph 2,073 RPM 2,235 RPM 2,397 RPM 2,768 RPM
70 mph 2,902 RPM 3,129 RPM 3,356 RPM 3,876 RPM

On this page, 3.31 gear ratio is the case in point: Read across any row and the trade is visible: at 70 mph the 3.31 ratio sits between the taller 3.07 and the shorter 4.10, and the gap between the extremes is about a third of the engine speed. That gap is the difference between a relaxed cruise and a busy one, and between soft acceleration and strong acceleration, which is why the ratio is chosen from the table rather than from the number alone. If the tyres are larger than the assumption here, every RPM figure falls; if they are smaller, every figure rises — rework the table with the actual diameter before deciding.

3.31 gear ratio: How tyre diameter changes the answer

Taking 3.31 gear ratio as the case in point: The tyre diameter belongs in the formula because it sets how far the vehicle moves per wheel revolution. A 35-inch tyre travels about 110 inches per turn while a 31-inch tyre travels about 97 inches, so the same driveshaft speed moves the bigger-tyre vehicle further and the engine turns more slowly at a given road speed. That is why a ratio that felt right on the original tyres can feel sluggish after a lift and bigger tyres: nothing about the engine changed, but the effective gearing grew taller by the same percentage as the diameter. The fix is a numerically higher ratio that brings the RPM back to where it was. All diameters quoted here are nominal new-tyre figures computed from the size code, and real tyres vary slightly by brand, model, wear and inflation pressure.

3.31 gear ratio: What the ratio does on the road

Taking 3.31 gear ratio as the case in point: The practical effects of a ratio are felt in three places: acceleration, cruising and towing. A numerically higher ratio multiplies torque more, so the vehicle pulls harder from rest and holds speed better with a trailer, and the engine reaches its useful RPM sooner after each shift. The same ratio raises cruising RPM, which means more noise and usually more fuel on a long steady run. A numerically lower ratio reverses all of that: calmer cruising and lower fuel use at steady speed, but softer acceleration and more frequent downshifts when the road rises or the load grows. Tyre size moves the whole picture — bigger tyres make any ratio act taller — so the right comparison is always ratio and tyre diameter together, never the ratio on its own. That is the comparison the tables in this article make.

How to find the ratio already fitted for 3.31 gear ratio

Taking 3.31 gear ratio as the case in point: Finding the ratio already fitted is a matter of looking in the right places. The axle tag, usually a small metal tag bolted to the differential cover, often stamps the ratio directly. The door-jamb placard and the owner's manual list the axle and tyre specification for the vehicle as built, and the build sheet or window sticker carries the same information in coded form. A VIN decoder can also return the original axle ratio, though it reports the vehicle as built rather than as it stands now, so it will not catch a previous owner's axle swap. The hands-on check is to count teeth: mark the ring gear and pinion, count the teeth on each, and divide ring teeth by pinion teeth — 41 ring teeth and 11 pinion teeth give 41 ÷ 11 = 3.73. If the tag, the paperwork and the tooth count disagree, the tooth count is the one to trust, because it describes the axle actually fitted.

3.31 gear ratio: Common mistakes with gear ratios

On this page, 3.31 gear ratio is the case in point: The most common mistake is changing the ratio without checking the tyre diameter, or changing the tyres without checking the ratio — the two are one calculation, and doing half of it leaves the gearing wrong in the other direction. The second is comparing ratios across vehicles with different tyre sizes: a 3.73 on 35-inch tyres is effectively taller gearing than a 3.73 on 31-inch tyres, so the number alone does not describe the driving experience. The third is forgetting the gearbox: the formula needs the gear ratio of the gear in use, and overdrive gears below 1.00 change the answer, so a table built for top gear does not apply in third. The fourth is treating a calculated RPM as a promise about fuel use — RPM is one input to consumption, not the whole story, and load, aerodynamics and driving style move the result. And the fifth is assuming a ratio change is a fitment approval: it is a calculation, and clearances, load ratings and the placard still need checking with a professional.

Related pages for 3.31 gear ratio

Frequently asked questions

What RPM does a 3.31 gear ratio give at 70 mph?

On this page, 3.31 gear ratio is the case in point: On 205/55R16 tyres (631.9 mm, 24.88 in) in top gear at 1.00, a 3.31 ratio gives 3,129 RPM at 70 mph, 2,235 RPM at 50 mph and 1,341 RPM at 30 mph. Those figures use the stated tyre diameter, so rework them with the actual diameter for a different tyre size — a 10% larger diameter cuts every RPM figure by roughly 9%.

Is a 3.31 gear ratio good for towing?

A 3.31 ratio is a middle-ground choice for towing: it multiplies torque more than a taller ratio such as 3.21, so it holds speed better on grades with a trailer, but less than a shorter ratio such as 4.10. Whether it suits a particular towing job depends on the trailer weight, the tyre diameter and the engine, so use the RPM table above with the actual figures and confirm with a drivetrain specialist. Never exceed the vehicle's tow rating, GVWR or GCWR.

How do I find out if my car has a 3.31 gear ratio?

Taking 3.31 gear ratio as the case in point: Check the metal tag on the differential cover, which usually stamps the ratio directly, then cross-check the door-jamb placard and the owner's manual. A VIN decoder returns the ratio the vehicle was built with. The conclusive check is counting teeth: divide the ring-gear teeth by the pinion teeth, so 41 ÷ 11 = 3.73. If the sources disagree, the tooth count describes the axle actually fitted.

Does changing the gear ratio affect the speedometer?

Taking 3.31 gear ratio as the case in point: Yes, indirectly: the speedometer is calibrated for a rolling circumference, and a ratio change does not change the tyre, so the speedometer reading itself is unaffected by the ratio alone. What changes is the engine speed at a given road speed. A tyre-size change does affect the speedometer, because it changes the rolling circumference — see the speedometer error calculator for that calculation.

Can I change my gear ratio myself?

For 3.31 gear ratio, the point is this: A ratio change means replacing the ring gear and pinion and setting the backlash and preload precisely, which is a specialist drivetrain job with special tools. An incorrect setup fails quickly and expensively. Most owners have the work done by a drivetrain specialist, who can also confirm the ratio suits the axle, the gearbox and the way the vehicle is used.