275/55R17 Tyre Size: Dimensions, Alternatives & Speedometer Effect
275/55R17 is a very wide mid-profile tyre size for a 17-inch rim, and the first thing to know about it is the overall diameter: 734.3 mm (28.91 inches). That single figure drives almost everything else on this page — the speedometer reading, the gearing, the ground clearance and which sizes can replace it without changing how the car behaves. The sidewall stands 151.2 mm tall, the tyre rolls 2306.9 mm around its circumference, and it turns 697.6 times for every mile travelled. If you are here because 275/55R17 is the size on your door-jamb placard, or because it is printed on the sidewall of the tyres on your car now, those four numbers are the ones to carry into any comparison.
In practical terms, 275/55R17 is a very wide mid-profile size for a 17-inch wheel. The combination matters because the width sets the contact patch, the aspect ratio sets how much rubber sits between the rim and the road, and the rim diameter sets which wheels the tyre will mount on. Change any one of the three numbers and the overall diameter — and with it the speedometer, the gearing and the ride — moves as well.
This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.
275/55R17 dimensions
| Measurement | Value |
|---|---|
| Overall diameter | 734.3 mm (28.91 in) |
| Sidewall height | 151.2 mm |
| Circumference | 2306.9 mm (90.82 in) |
| Revolutions per mile | 697.6 |
| Revolutions per kilometre | 433.5 |
| Rim diameter | 17 in (431.8 mm) |
These are nominal new-tyre figures, worked out from the size code itself: the diameter is the rim diameter plus twice the sidewall height, the circumference is pi times the diameter, and the revolutions per mile follow from the circumference. Real tyres vary slightly by brand, model, wear and inflation pressure, so two tyres marked 275/55R17 can differ by a millimetre or two in practice — the table gives the standard computed values, which are the right ones to use for comparisons. For scale, 275/55R17 is 16.21% larger in diameter than the widely used 205/55R16 reference size (631.9 mm), so a car moving from that reference size to 275/55R17 would see its speedometer, gearing and ride height shift by that proportion. The ±3% guideline around 275/55R17 runs from 712.3 mm to 756.3 mm: replacements inside that band keep the speedometer error small, and replacements outside it deserve a closer look before fitting.
Decoding 275/55R17: width, aspect ratio and rim
The code 275/55R17 breaks into three parts, and each part is a measurement. The first number, 275, is the section width in millimetres — the width of the tyre from one sidewall to the other at its widest point, measured on its approved rim width. The second number, 55, is the aspect ratio: the sidewall height expressed as a percentage of the width, so 55% of 275 mm gives the 151.2 mm sidewall in the table. The letter R means radial construction, which is the standard for modern road tyres, and the final number, 17, is the rim diameter in inches — the wheel this tyre mounts on. Put together, the diameter is 431.8 mm of rim plus two sidewalls of 151.2 mm, which is 431.8 + 302.4 = 734.3 mm, matching the table. That arithmetic is worth doing once by hand, because it shows why two sizes that look similar can measure differently: raising the aspect ratio by 5 points on a 275 mm width adds 13.8 mm to each sidewall and 27.5 mm to the diameter, while widening the section by 10 mm at the same aspect ratio adds 5.5 mm per sidewall. The size code tells you nothing about load index or speed rating — those are separate markings on the sidewall, and the placard specifies the minimum for both.
Closest alternatives to 275/55R17
The three sizes in the chart closest to 275/55R17 by overall diameter are listed below. Each one is a real size from the same chart, with its diameter difference worked out against 734.3 mm, so the comparison is exact rather than approximate.
| Alternative size | Diameter (mm) | Difference (mm) | Difference (%) | Actual speed at 60 mph indicated | Rim |
|---|---|---|---|---|---|
| 235/75R15 | 733.5 | -0.8 | -0.11% | 59.9 mph | 15 in |
| 235/70R16 | 735.4 | 1.1 | 0.15% | 60.1 mph | 16 in |
| 285/35R21 | 732.9 | -1.4 | -0.19% | 59.9 mph | 21 in |
235/75R15 measures 733.5 mm across, 0.8 mm shorter than 275/55R17, a difference of 0.11%. Fitted in place of 275/55R17 it would lift or lower the car by about 0.4 mm — half the diameter change — and at an indicated 60 mph the car would actually be travelling at 59.9 mph. Its sidewall is 176.2 mm on a 15-inch rim, it turns 698.4 times per mile, and its circumference is 2304.4 mm. That puts it inside the ±3% guideline around 275/55R17, so it is a change the speedometer would barely notice.
235/70R16 measures 735.4 mm across, 1.1 mm taller than 275/55R17, a difference of 0.15%. Fitted in place of 275/55R17 it would lift or lower the car by about 0.6 mm — half the diameter change — and at an indicated 60 mph the car would actually be travelling at 60.1 mph. Its sidewall is 164.5 mm on a 16-inch rim, it turns 696.6 times per mile, and its circumference is 2310.3 mm. That puts it inside the ±3% guideline around 275/55R17, so it is a change the speedometer would barely notice.
285/35R21 measures 732.9 mm across, 1.4 mm shorter than 275/55R17, a difference of 0.19%. Fitted in place of 275/55R17 it would lift or lower the car by about 0.7 mm — half the diameter change — and at an indicated 60 mph the car would actually be travelling at 59.9 mph. Its sidewall is 99.8 mm on a 21-inch rim, it turns 699.0 times per mile, and its circumference is 2302.5 mm. That puts it inside the ±3% guideline around 275/55R17, so it is a change the speedometer would barely notice.
For 275/55R17, a useful way to use this table is to start from the diameter difference column, comparing each alternative with 235/75R15 first. Anything inside ±3% keeps the speedometer, the gearing and the ride height close to the original, and most drivers would not notice the change in daily driving. Anything outside that band changes the car's behaviour in ways that are easy to measure — the speedometer error grows, the gearing lengthens or shortens, and the ride height moves — so it needs the placard check and a professional's confirmation before fitting. Rim size matters here too: the alternatives above use 15-, 16- and 21-inch rims, and a size on a different rim diameter needs different wheels, not just different tyres.
275/55R17 and your speedometer
The speedometer is calibrated for the original diameter, so any change in diameter changes what the dial shows. The formula is straightforward: error % = (new diameter − old diameter) ÷ old diameter × 100, and actual speed = indicated speed × (new diameter ÷ old diameter). For the closest alternative, 235/75R15 (733.5 mm against 734.3 mm, a -0.11% change), the numbers work out as follows:
| Indicated speed | Actual speed on 235/75R15 | Actual at +3% diameter | Actual at −3% diameter |
|---|---|---|---|
| 30 mph | 30.0 mph | 30.9 mph | 29.1 mph |
| 50 mph | 49.9 mph | 51.5 mph | 48.5 mph |
| 70 mph | 69.9 mph | 72.1 mph | 67.9 mph |
For 275/55R17, a 0.11% diameter change sounds small, and at 30 mph it is — the difference is under a mile per hour either way. At 70 mph the same percentage is worth a little more, which is why motorway driving is where a size change shows up first. The +3% and −3% columns show the edges of the usual guideline: at the +3% edge the car is travelling about 2 mph faster than the dial at 70 mph, and at the −3% edge about 2 mph slower. That is the reason the guideline is ±3% rather than a wider band — beyond it, the error at motorway speed starts to matter for speed limits and for the odometer, which records distance from the same wheel-speed signal and so drifts by the same percentage. A tyre change also affects the odometer reading, the gearing and, on some cars, the calibration of driver-assistance systems that use wheel speed.
Going wider or taller than 275/55R17
Going wider than 275/55R17 — for example to a 235/75R15 if its width is greater — puts more rubber on the road, which can sharpen dry grip and steering response, but it also adds rolling resistance and can make the steering feel heavier, and the extra width needs clearance at the arch, the suspension and full steering lock. Going taller raises the overall diameter, lifts the car by half the diameter increase, lengthens the gearing slightly and slows the speedometer reading relative to actual speed. Going narrower or shorter does the opposite: lighter steering and a little less rolling resistance, but a smaller contact patch and a speedometer that reads high. None of these effects is large for a change inside the ±3% guideline, which is why that guideline exists — it keeps the gearing, the speedometer and the clearance close to what the vehicle was designed around.
Ride quality follows the sidewall. The 151.2 mm sidewall on 275/55R17 is 55.0% of the section width, and it is the cushion between the rim and the road: a taller sidewall absorbs small bumps and protects the rim from pothole damage, while a shorter sidewall gives sharper steering response and less flex in corners. That is the trade behind the mid-profile label — 275/55R17 is neither the softest nor the sharpest option in its rim size, and moving to a much lower aspect ratio on the same rim would firm the ride noticeably, while moving to a much taller one would soften it. Fuel use moves with rolling resistance, which tends to rise with width and fall slightly with a taller, more flexible sidewall, but the differences between sizes inside the ±3% band are small compared with the differences that pressure, tread pattern and driving style make. Keep the pressures at the placard figure for the size fitted, checked cold, and the tyre will perform as its size suggests it should.
Before fitting 275/55R17: the checks that matter
The checks for 275/55R17 start from the same place every time: the 734.3 mm diameter on the placard, and the load and speed ratings that go with it. Do the checks in order. First, the door-jamb placard: it is the manufacturer's statement of which size, pressures, load index and speed rating the vehicle was built around. Second, the owner's manual, which confirms the placard and covers the spare. Third, the sidewall of the tyre on the car now — if it reads something other than the placard size, treat that as a question to answer, not as the specification. Fourth, the load index and speed rating on the replacement: both must meet or exceed what the placard requires, because a tyre that is the right size but the wrong load index is still the wrong tyre. Fifth, rim width: a 275 mm section mounts correctly only on a rim within its approved width range. Sixth, the pressure monitoring system, which may need a reset after any change in rolling circumference. Winter tyres deserve the same checks, not fewer — the size rules do not relax in cold weather.
One more check belongs on the list for 275/55R17: the spare. If the car carries a full-size spare, it should match the 734.3 mm size and the load index of the road tyres; if it carries a space-saver, its size and its speed limit are different by design and it is for getting to a repair, not for normal driving. And when the new tyres are fitted, check the pressures again after a short drive and a cool-down, because a tyre that was fitted warm can read differently once it is cold. The placard pressure is a cold pressure, and it is the figure to use for 275/55R17, not a figure carried over from a different size.
Common mistakes with 275/55R17
With 275/55R17, the errors are rarely about the 275 mm width on its own — they are about the 55% aspect ratio and the 17-inch rim that go with it. People go wrong with 275/55R17 in a handful of repeatable ways. One is to match the width (275 mm) and ignore the aspect ratio (55%) — two tyres with the same width and different aspect ratios have different diameters, so the speedometer and gearing change. Another is to copy the size already on the car without checking the door-jamb placard, which is how a previous owner's wrong choice gets repeated. A third is to buy on size alone and overlook the load index and speed rating, which the placard also specifies. A fourth is to change the size on one axle and not the other, leaving different rolling circumferences front and rear that traction control and all-wheel drive were not designed for. And a fifth is to fit the new tyres and keep the old pressures: the correct pressure is the placard figure for the size fitted, checked cold, not a number remembered from the old set.
The last mistake is a quiet one: assuming the size code is the whole specification. 275/55R17 fixes the width, the aspect ratio and the rim, but it does not fix the load index, the speed rating, the tread pattern or the compound, and two tyres marked 275/55R17 can still be very different tyres. Read the full sidewall, match the load index and speed rating to the placard, and choose the tread and compound for the driving the car actually does. The size gets you to the right shelf; the rest of the sidewall gets you to the right tyre.
Related sizes and tools for 275/55r17 tyre size
If 275/55R17 is your starting point, the closest sizes to compare are 235/75R15 tyre size, 235/70R16 tyre size, 285/35R21 tyre size. The tyre size calculator page explains how to decode any size code and work out its dimensions, and the tyre size calculator tool does the arithmetic for any size in the chart. The tyre sizes hub lists every size covered on this site, and the tyre size chart shows the full computed table side by side.
Frequently asked questions
What is the overall diameter of 275/55R17?
The overall diameter of 275/55R17 is 734.3 mm, which is 28.91 inches. That is the rim diameter of 17 inches (431.8 mm) plus two sidewalls of 151.2 mm each. It is a nominal new-tyre figure; real tyres vary slightly by brand, model, wear and inflation pressure.
What is the sidewall height of 275/55R17?
The sidewall height of 275/55R17 is 151.2 mm. It comes from the aspect ratio: 55% of the 275 mm section width is 275 × 55 ÷ 100 = 151.2 mm. That mid-profile sidewall is the cushion between the 17-inch rim and the road, and it is what gives 275/55R17 its ride and steering character.
How many revolutions per mile does 275/55R17 do?
275/55R17 turns 697.6 times per mile, or about 433.5 times per kilometre. The figure follows from the circumference of 2306.9 mm: one mile is 63,360 inches, and each revolution covers one circumference. A replacement tyre with a different circumference turns a different number of times per mile, which is why the speedometer and odometer readings move when the diameter changes.
What is the closest alternative size to 275/55R17?
The closest size in the chart to 275/55R17 is 235/75R15, at 733.5 mm — 0.11% smaller in diameter than 275/55R17. At an indicated 60 mph the car would actually be travelling at 59.9 mph on 235/75R15. The next closest are 235/70R16 (0.15%) and 285/35R21 (-0.19%), and all three are listed with their full figures in the alternatives table above.
Does 275/55R17 affect the speedometer?
Yes — fitting 275/55R17 in place of a different original size changes the reading, because the speedometer is calibrated for the diameter the car was built with, so fitting 275/55R17 in place of a size with a different diameter changes the reading by the diameter difference as a percentage. A replacement within ±3% of the original diameter — between 712.3 mm and 756.3 mm for 275/55R17 — keeps the error small; outside that band the error at motorway speed becomes noticeable, and the odometer drifts by the same percentage.
Can I fit 275/55R17 instead of my current size?
For 275/55R17, only if the diameter stays within about ±3% of the size on your door-jamb placard, the load index and speed rating meet what the placard specifies, the rim width suits a 275 mm section, and there is clearance at the arch, the suspension and full steering lock. This page gives the measurements so you can make that comparison; it does not approve a fitment. Check the placard and confirm with a tyre professional before fitting a different size.