Speedometer Error Calculator: Formula, Worked Example & Speed Tables

Speedometer Error Calculator is answered by one formula and two tyre diameters. Error % = (new diameter − old diameter) ÷ old diameter × 100, and actual speed = indicated speed × (new diameter ÷ old diameter). This page applies the formula to the question in the keyword with a worked example using real tyre sizes, tables at 30, 50 and 70 mph, and the practical consequences explained in plain terms. The worked example uses 205/55R16 (631.9 mm) replaced by 215/55R16 (642.9 mm), a +1.74% change, and the tables use the nominal new-tyre diameters computed from the size codes — real tyres vary slightly by brand, model, wear and inflation pressure.

On this page, speedometer error calculator is the case in point: The reason the error matters is that it is proportional: the same percentage applies at every speed and to the odometer as well, so a small percentage becomes a meaningful mph difference at motorway speed and a meaningful mileage difference over a year. A larger tyre makes the dial read low, so the car travels faster than the driver believes, and a smaller tyre makes it read high. The sections below show the arithmetic, the tables, the common causes of a wrong reading, how to check the dial against GPS, and when a recalibration is needed.

This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.

How the speedometer error is calculated for speedometer error calculator

Work it out in two steps. Step one, the percentage: error % = (new diameter − old diameter) ÷ old diameter × 100, using the nominal new-tyre diameters computed from the size codes. Step two, the actual speed at any indicated speed: actual speed = indicated speed × (new diameter ÷ old diameter). A tyre that is 2% larger in diameter gives an actual speed 2% above the indicated speed — 71.4 mph actual at an indicated 70 mph — and a tyre 2% smaller gives 68.6 mph actual at the same indicated speed. The odometer follows the same percentage, so the mileage it records is also out by that amount. All the tables below are built from those two formulas with the diameters stated. That is the point this page works through for speedometer error calculator.

What the speedometer actually measures for speedometer error calculator

For speedometer error calculator, the point is this: A speedometer measures how fast the wheels are turning and converts that into a road speed using the rolling circumference of the tyres it was calibrated for. Change the tyre diameter and the conversion is wrong by exactly the percentage the diameter changed: a tyre 3% larger in diameter covers 3% more ground per revolution, so the car travels 3% faster than the dial shows, and the odometer records 3% fewer miles than the car actually covers. A tyre 3% smaller does the opposite. The error is proportional at every speed, which is why the tables in this article show the same percentage at 30, 50 and 70 mph, and why the formula below is all that is needed to work out the error for any size change.

speedometer error calculator: Worked example: 205/55R16 to 215/55R16

Taking speedometer error calculator as the case in point: 205/55R16 measures 631.9 mm in overall diameter and 215/55R16 measures 642.9 mm. The error % is (642.9 − 631.9) ÷ 631.9 × 100 = +1.74%. At an indicated 30 mph the actual speed is 30 × (642.9 ÷ 631.9) = 30.5 mph; at 50 mph it is 50.9 mph; and at 70 mph it is 71.2 mph. The odometer is out by the same 1.74%: it records 98.29 miles for every 100 miles actually driven. The diameter change of 1.74% is inside the ±3% guideline commonly used for keeping speedometer error small, which is why this pair is a useful example — a larger change, such as 235/65R17 (737.3 mm) to 265/70R17 (802.8 mm), is +8.89% and gives 76.2 mph actual at an indicated 70 mph.

Indicated vs actual speed: the worked example for speedometer error calculator

Taking speedometer error calculator as the case in point: Error: +1.74%. Actual speed = indicated speed × (642.9 ÷ 631.9).

Indicated speed Actual speed Difference
30 mph 30.5 mph +0.5 mph
50 mph 50.9 mph +0.9 mph
70 mph 71.2 mph +1.2 mph

On this page, speedometer error calculator is the case in point: The table is read from the indicated speed: find the dial reading and read across for the actual speed. The difference column is the amount by which the car is travelling faster than the dial shows, and it grows with speed because the error is a percentage. A 1.74% error is 0.5 mph at 30 mph and 1.2 mph at 70 mph — small in both cases, but the direction is the one that matters, because the car is going faster than the driver believes. Check the door-jamb placard for the specified size and confirm fitment with a tyre professional before fitting a different tyre size.

Common causes of a wrong speedometer for speedometer error calculator

For speedometer error calculator, the point is this: The causes divide into calibration and faults, and the distinction decides the fix. Calibration causes are tyre diameter changes, wear and inflation pressure: all of them change the distance covered per wheel revolution, and all of them produce a steady percentage error that the formulas on this page can predict. Fault causes are a failing wheel-speed sensor, a damaged reluctor ring, a worn speedometer cable on older vehicles, or a fault in the instrument cluster itself — these usually make the reading jump, stick or drop to zero rather than sit a steady percentage out. If the error is the same percentage at every speed, it is calibration; if it changes with speed or the needle behaves erratically, it is a fault and the vehicle needs diagnosis rather than a recalibration.

speedometer error calculator: How to fix a speedometer error

Taking speedometer error calculator as the case in point: Fixing a speedometer error means telling the vehicle the new tyre diameter, and the method depends on the vehicle. On many modern cars a handheld programmer or a diagnostic tool can rewrite the tyre-size setting in the body or engine control module, and the speedometer and odometer then read correctly for the new size. On older vehicles with a mechanical speedometer, the fix is a different speedometer drive gear in the gearbox, chosen so the gear ratio compensates for the diameter change. Some vehicles need a dealer visit because the setting is locked behind manufacturer software, and some need an inline speedometer calibrator fitted in the sensor wiring. Whichever method is used, the correct one depends on the vehicle, so the owner's manual or a specialist should be consulted before buying a tool — and the error should be measured against GPS before and after, at a steady speed, to confirm the fix worked.

speedometer error calculator: Common mistakes with speedometer error

Taking speedometer error calculator as the case in point: The most common mistake is assuming the speedometer was accurate before the tyre change. Most speedometers are deliberately calibrated to read slightly high — in the UK the law requires that a speedometer never under-reads, and it may over-read by up to 10% plus 4 km/h — so a car that read 2% high on the original tyres and now reads 2% low on larger tyres has actually changed by 4% from what the driver was used to. The second mistake is checking the speedometer against another car's speedometer instead of against GPS: two dials can share the same error. The third is testing at one speed only and assuming the error is a fixed number of mph — it is a percentage, so the mph error grows with speed. And the fourth is treating a calculation as a reason to ignore the limit: if the dial reads low, the car is travelling faster than the driver thinks, and that is the direction that risks a speeding offence.

Related pages for speedometer error calculator

Frequently asked questions

How do I calculate speedometer error for speedometer error calculator?

For speedometer error calculator, the point is this: Use error % = (new diameter − old diameter) ÷ old diameter × 100, then actual speed = indicated speed × (new diameter ÷ old diameter). The worked example above uses 205/55R16 (631.9 mm) and 215/55R16 (642.9 mm), a +1.74% change, and the speedometer error calculator runs the same formula with your own sizes.

How much can a speedometer be out?

Taking speedometer error calculator as the case in point: It depends on the tyre change. A 1% diameter change is 0.7 mph at an indicated 70 mph; a 3% change is 2.1 mph; an 8.89% change, such as 235/65R17 to 265/70R17, is 6.2 mph at an indicated 70 mph. In the UK the law requires that a speedometer never under-reads and may over-read by up to 10% plus 4 km/h.

Why is my speedometer wrong after new tyres?

For speedometer error calculator, the point is this: The usual reason is a different diameter from the size the vehicle was calibrated for: a larger tyre makes the dial read low and a smaller tyre makes it read high, by the diameter percentage. Other causes are wear, pressure, a previous recalibration for a different size, or a sensor fault. Measure the error against GPS at a steady speed to find out which it is.

How do I check my speedometer against GPS?

On this page, speedometer error calculator is the case in point: Drive at a steady speed on a straight, level road and compare the dial with a GPS speed reading. GPS is least reliable at low speed, while accelerating or braking, and on hills or in tunnels, so take the reading at a steady cruise. A difference that is the same percentage at several speeds is a calibration error; a needle that jumps or sticks is a fault.

Does tyre wear affect the speedometer?

On this page, speedometer error calculator is the case in point: Yes, slightly. A worn tyre has a smaller diameter than a new one, so the speedometer reads slightly high as the tread wears — typically well under 1% over the life of the tyre. Under-inflation has the same direction of effect by reducing the effective rolling radius. Both are small compared with a size change, but they are real.