Speedometer Accuracy Calculator: Formula, Worked Example & Speed Tables

Speedometer Accuracy Calculator is answered by one formula and two tyre diameters. Error % = (new diameter − old diameter) ÷ old diameter × 100, and actual speed = indicated speed × (new diameter ÷ old diameter). This page applies the formula to the question in the keyword with a worked example using real tyre sizes, tables at 30, 50 and 70 mph, and the practical consequences explained in plain terms. The worked example uses 205/55R16 (631.9 mm) replaced by 215/55R16 (642.9 mm), a +1.74% change, and the tables use the nominal new-tyre diameters computed from the size codes — real tyres vary slightly by brand, model, wear and inflation pressure.

Taking speedometer accuracy calculator as the case in point: The reason the error matters is that it is proportional: the same percentage applies at every speed and to the odometer as well, so a small percentage becomes a meaningful mph difference at motorway speed and a meaningful mileage difference over a year. A larger tyre makes the dial read low, so the car travels faster than the driver believes, and a smaller tyre makes it read high. The sections below show the arithmetic, the tables, the common causes of a wrong reading, how to check the dial against GPS, and when a recalibration is needed.

This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.

How the speedometer error is calculated for speedometer accuracy calculator

Work it out in two steps. Step one, the percentage: error % = (new diameter − old diameter) ÷ old diameter × 100, using the nominal new-tyre diameters computed from the size codes. Step two, the actual speed at any indicated speed: actual speed = indicated speed × (new diameter ÷ old diameter). A tyre that is 2% larger in diameter gives an actual speed 2% above the indicated speed — 71.4 mph actual at an indicated 70 mph — and a tyre 2% smaller gives 68.6 mph actual at the same indicated speed. The odometer follows the same percentage, so the mileage it records is also out by that amount. All the tables below are built from those two formulas with the diameters stated. That is the point this page works through for speedometer accuracy calculator.

speedometer accuracy calculator: What the speedometer actually measures

Speedometer error is a percentage, not a fixed number of miles per hour, and that is the key to understanding it. The dial shows the speed the car would be doing if the original tyres were fitted, and the actual speed is the indicated speed multiplied by the ratio of the new diameter to the old diameter. A small diameter change gives a small error — a 1% change is 0.7 mph at an indicated 70 mph — while a large change gives an error that matters for speed limits and for the odometer. Because the error is proportional, the same table works at any speed once the percentage is known, and the worked examples in this article show how to find that percentage from the two tyre sizes. That is the point this page works through for speedometer accuracy calculator.

Worked example: 205/55R16 to 215/55R16 for speedometer accuracy calculator

On this page, speedometer accuracy calculator is the case in point: 205/55R16 measures 631.9 mm in overall diameter and 215/55R16 measures 642.9 mm. The error % is (642.9 − 631.9) ÷ 631.9 × 100 = +1.74%. At an indicated 30 mph the actual speed is 30 × (642.9 ÷ 631.9) = 30.5 mph; at 50 mph it is 50.9 mph; and at 70 mph it is 71.2 mph. The odometer is out by the same 1.74%: it records 98.29 miles for every 100 miles actually driven. The diameter change of 1.74% is inside the ±3% guideline commonly used for keeping speedometer error small, which is why this pair is a useful example — a larger change, such as 235/65R17 (737.3 mm) to 265/70R17 (802.8 mm), is +8.89% and gives 76.2 mph actual at an indicated 70 mph.

Indicated vs actual speed: the worked example for speedometer accuracy calculator

On this page, speedometer accuracy calculator is the case in point: Error: +1.74%. Actual speed = indicated speed × (642.9 ÷ 631.9).

Indicated speed Actual speed Difference
30 mph 30.5 mph +0.5 mph
50 mph 50.9 mph +0.9 mph
70 mph 71.2 mph +1.2 mph

Taking speedometer accuracy calculator as the case in point: The table is read from the indicated speed: find the dial reading and read across for the actual speed. The difference column is the amount by which the car is travelling faster than the dial shows, and it grows with speed because the error is a percentage. A 1.74% error is 0.5 mph at 30 mph and 1.2 mph at 70 mph — small in both cases, but the direction is the one that matters, because the car is going faster than the driver believes. Check the door-jamb placard for the specified size and confirm fitment with a tyre professional before fitting a different tyre size.

Common causes of a wrong speedometer for speedometer accuracy calculator

Taking speedometer accuracy calculator as the case in point: The causes divide into calibration and faults, and the distinction decides the fix. Calibration causes are tyre diameter changes, wear and inflation pressure: all of them change the distance covered per wheel revolution, and all of them produce a steady percentage error that the formulas on this page can predict. Fault causes are a failing wheel-speed sensor, a damaged reluctor ring, a worn speedometer cable on older vehicles, or a fault in the instrument cluster itself — these usually make the reading jump, stick or drop to zero rather than sit a steady percentage out. If the error is the same percentage at every speed, it is calibration; if it changes with speed or the needle behaves erratically, it is a fault and the vehicle needs diagnosis rather than a recalibration.

speedometer accuracy calculator: How to fix a speedometer error

On this page, speedometer accuracy calculator is the case in point: The fix is chosen by vehicle, not by preference. Modern vehicles with electronic speedometers are usually corrected by reprogramming the tyre-size setting with a diagnostic tool or a handheld programmer, which adjusts the speedometer and the odometer together. Older vehicles with a cable-driven speedometer need a different speedometer drive gear, and the new gear is selected using the diameter ratio — new teeth = old teeth × (old diameter ÷ new diameter) — so the gear compensates exactly for the size change. Where neither is available, an inline signal calibrator fitted to the speed sensor wiring can scale the reading. A dealer may be needed where the setting is locked behind manufacturer software. In every case, measure the error against GPS before and after the fix, at a steady speed on a straight road, to confirm the dial is right.

Common mistakes with speedometer error for speedometer accuracy calculator

For speedometer accuracy calculator, the point is this: Mistakes usually start with the wrong reference. The first is comparing the dial with another vehicle's dial — both can be out by the same amount. GPS speed, measured at a steady speed on a straight road, is the practical reference, though it has its own limits at low speed and on hills. The second mistake is treating the error as a fixed mph figure: a 3% error is 0.9 mph at 30 mph and 2.1 mph at 70 mph, so a single-speed check does not describe the whole picture. The third is forgetting that most speedometers already read slightly high from the factory, so the error after a tyre change is measured from that baseline, not from zero. And the fourth is the dangerous one: fitting larger tyres makes the dial read low, so the car is going faster than the driver believes, and driving to the indicated limit in that condition means exceeding it.

speedometer accuracy calculator: Related pages

Frequently asked questions

How do I calculate speedometer error for speedometer accuracy calculator?

For speedometer accuracy calculator, the point is this: Use error % = (new diameter − old diameter) ÷ old diameter × 100, then actual speed = indicated speed × (new diameter ÷ old diameter). The worked example above uses 205/55R16 (631.9 mm) and 215/55R16 (642.9 mm), a +1.74% change, and the speedometer error calculator runs the same formula with your own sizes.

How much can a speedometer be out?

For speedometer accuracy calculator, the point is this: It depends on the tyre change. A 1% diameter change is 0.7 mph at an indicated 70 mph; a 3% change is 2.1 mph; an 8.89% change, such as 235/65R17 to 265/70R17, is 6.2 mph at an indicated 70 mph. In the UK the law requires that a speedometer never under-reads and may over-read by up to 10% plus 4 km/h.

Why is my speedometer wrong after new tyres?

For speedometer accuracy calculator, the point is this: The usual reason is a different diameter from the size the vehicle was calibrated for: a larger tyre makes the dial read low and a smaller tyre makes it read high, by the diameter percentage. Other causes are wear, pressure, a previous recalibration for a different size, or a sensor fault. Measure the error against GPS at a steady speed to find out which it is.

How do I check my speedometer against GPS?

Taking speedometer accuracy calculator as the case in point: Drive at a steady speed on a straight, level road and compare the dial with a GPS speed reading. GPS is least reliable at low speed, while accelerating or braking, and on hills or in tunnels, so take the reading at a steady cruise. A difference that is the same percentage at several speeds is a calibration error; a needle that jumps or sticks is a fault.

Does tyre wear affect the speedometer?

For speedometer accuracy calculator, the point is this: Yes, slightly. A worn tyre has a smaller diameter than a new one, so the speedometer reads slightly high as the tread wears — typically well under 1% over the life of the tyre. Under-inflation has the same direction of effect by reducing the effective rolling radius. Both are small compared with a size change, but they are real.