How to Recalibrate Speedometer: Methods, Costs & When It Is Needed

Calibrating a speedometer after a tyre change means telling the vehicle the new tyre diameter, and whether it is needed depends on how far out the dial is and in which direction. A small change inside the ±3% guideline often leaves the dial reading slightly high, which is the safe direction and the direction the law requires in the UK; a larger change, or one that makes the dial under-read, is the case for recalibration. This page explains how to measure the error, the four correction methods — programmer, dealer software, speedometer gear and inline calibrator — and how to check the result afterwards, with a worked example using 205/55R16 and 215/55R16. That is the point this page works through for how to recalibrate speedometer.

Taking how to recalibrate speedometer as the case in point: The worked example uses 205/55R16 (631.9 mm) replaced by 215/55R16 (642.9 mm), a +1.74% change, so at an indicated 70 mph the actual speed is 71.2 mph. That is a small error in the direction that makes the car travel faster than the dial shows, and it is worth knowing about even if a recalibration is not needed. The sections below cover the measurement, the methods, the costs and the checks — and the reminder that the correct method depends on the vehicle, so the owner's manual or a specialist should be consulted before buying a tool.

This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.

How the speedometer error is calculated for how to recalibrate speedometer

On this page, how to recalibrate speedometer is the case in point: Work it out in two steps. Step one, the percentage: error % = (new diameter − old diameter) ÷ old diameter × 100, using the nominal new-tyre diameters computed from the size codes. Step two, the actual speed at any indicated speed: actual speed = indicated speed × (new diameter ÷ old diameter). A tyre that is 2% larger in diameter gives an actual speed 2% above the indicated speed — 71.4 mph actual at an indicated 70 mph — and a tyre 2% smaller gives 68.6 mph actual at the same indicated speed. The odometer follows the same percentage, so the mileage it records is also out by that amount. All the tables below are built from those two formulas with the diameters stated.

What the speedometer actually measures for how to recalibrate speedometer

Taking how to recalibrate speedometer as the case in point: The speedometer does not measure speed directly. It counts wheel revolutions — from a sensor on the gearbox output, a wheel-speed sensor or the ABS system, depending on the vehicle — and multiplies by the rolling circumference the manufacturer programmed in. That circumference belongs to the original tyre size, so fitting a different diameter changes the distance covered per revolution while the speedometer keeps using the old figure. The result is a fixed percentage error: if the new tyre is 2% larger in diameter, the actual speed is 2% higher than the indicated speed at every speed, and the odometer under-records by the same 2%. The error does not grow or shrink with speed; it is the same percentage at 30 mph and at 70 mph, which is what the tables below show.

how to recalibrate speedometer: Worked example: 205/55R16 to 215/55R16

Taking how to recalibrate speedometer as the case in point: 205/55R16 measures 631.9 mm in overall diameter and 215/55R16 measures 642.9 mm. The error % is (642.9 − 631.9) ÷ 631.9 × 100 = +1.74%. At an indicated 30 mph the actual speed is 30 × (642.9 ÷ 631.9) = 30.5 mph; at 50 mph it is 50.9 mph; and at 70 mph it is 71.2 mph. The odometer is out by the same 1.74%: it records 98.29 miles for every 100 miles actually driven. The diameter change of 1.74% is inside the ±3% guideline commonly used for keeping speedometer error small, which is why this pair is a useful example — a larger change, such as 235/65R17 (737.3 mm) to 265/70R17 (802.8 mm), is +8.89% and gives 76.2 mph actual at an indicated 70 mph.

Indicated vs actual speed: the worked example for how to recalibrate speedometer

Taking how to recalibrate speedometer as the case in point: Error: +1.74%. Actual speed = indicated speed × (642.9 ÷ 631.9).

Indicated speed Actual speed Difference
30 mph 30.5 mph +0.5 mph
50 mph 50.9 mph +0.9 mph
70 mph 71.2 mph +1.2 mph

On this page, how to recalibrate speedometer is the case in point: The table is read from the indicated speed: find the dial reading and read across for the actual speed. The difference column is the amount by which the car is travelling faster than the dial shows, and it grows with speed because the error is a percentage. A 1.74% error is 0.5 mph at 30 mph and 1.2 mph at 70 mph — small in both cases, but the direction is the one that matters, because the car is going faster than the driver believes. Check the door-jamb placard for the specified size and confirm fitment with a tyre professional before fitting a different tyre size.

how to recalibrate speedometer: Common causes of a wrong speedometer

On this page, how to recalibrate speedometer is the case in point: Several things can put a speedometer out, and they are worth separating because the fixes differ. The first is tyre diameter: any change from the size the vehicle was calibrated for produces a fixed percentage error, and it is the cause this article is about. The second is wear and pressure: a worn tyre is smaller than a new one and an under-inflated tyre has a smaller effective rolling radius, so both make the dial read slightly high. The third is a previous recalibration — a programmer setting or a speedometer gear fitted for an earlier tyre size that no longer matches what is on the car. The fourth is a fault: a failing wheel-speed sensor, a damaged reluctor ring or, on older cars, a worn cable, which usually shows as a needle that jumps, sticks or reads inconsistently rather than a steady percentage error. A steady percentage error points at calibration; an erratic needle points at a fault.

How to fix a speedometer error for how to recalibrate speedometer

There are four common ways to correct a speedometer after a tyre change, and the right one depends on the vehicle. A handheld programmer or diagnostic tool can change the programmed tyre size on many modern vehicles, which corrects both the speedometer and the odometer at once. A speedometer drive gear — a small gear in the gearbox — does the same job mechanically on older vehicles, and the replacement gear is chosen from the diameter ratio. An inline calibrator, wired into the speed sensor signal, can scale the signal on vehicles where neither of the above is possible. And a dealer recalibration uses manufacturer software to change the setting where it is locked to franchised tools. Before spending money on any of them, measure the error against GPS at a steady speed so the correction needed is known, and confirm the method suits the vehicle — the wrong tool for the vehicle wastes the money and leaves the dial wrong. That is the point this page works through for how to recalibrate speedometer.

how to recalibrate speedometer: Common mistakes with speedometer error

For how to recalibrate speedometer, the point is this: The most common mistake is assuming the speedometer was accurate before the tyre change. Most speedometers are deliberately calibrated to read slightly high — in the UK the law requires that a speedometer never under-reads, and it may over-read by up to 10% plus 4 km/h — so a car that read 2% high on the original tyres and now reads 2% low on larger tyres has actually changed by 4% from what the driver was used to. The second mistake is checking the speedometer against another car's speedometer instead of against GPS: two dials can share the same error. The third is testing at one speed only and assuming the error is a fixed number of mph — it is a percentage, so the mph error grows with speed. And the fourth is treating a calculation as a reason to ignore the limit: if the dial reads low, the car is travelling faster than the driver thinks, and that is the direction that risks a speeding offence.

Related pages for how to recalibrate speedometer

Frequently asked questions

How do I calculate speedometer error for how to recalibrate speedometer?

For how to recalibrate speedometer, the point is this: Use error % = (new diameter − old diameter) ÷ old diameter × 100, then actual speed = indicated speed × (new diameter ÷ old diameter). The worked example above uses 205/55R16 (631.9 mm) and 215/55R16 (642.9 mm), a +1.74% change, and the speedometer error calculator runs the same formula with your own sizes.

How much can a speedometer be out?

On this page, how to recalibrate speedometer is the case in point: It depends on the tyre change. A 1% diameter change is 0.7 mph at an indicated 70 mph; a 3% change is 2.1 mph; an 8.89% change, such as 235/65R17 to 265/70R17, is 6.2 mph at an indicated 70 mph. In the UK the law requires that a speedometer never under-reads and may over-read by up to 10% plus 4 km/h.

Why is my speedometer wrong after new tyres?

Taking how to recalibrate speedometer as the case in point: The usual reason is a different diameter from the size the vehicle was calibrated for: a larger tyre makes the dial read low and a smaller tyre makes it read high, by the diameter percentage. Other causes are wear, pressure, a previous recalibration for a different size, or a sensor fault. Measure the error against GPS at a steady speed to find out which it is.

How do I check my speedometer against GPS?

For how to recalibrate speedometer, the point is this: Drive at a steady speed on a straight, level road and compare the dial with a GPS speed reading. GPS is least reliable at low speed, while accelerating or braking, and on hills or in tunnels, so take the reading at a steady cruise. A difference that is the same percentage at several speeds is a calibration error; a needle that jumps or sticks is a fault.

Does tyre wear affect the speedometer?

On this page, how to recalibrate speedometer is the case in point: Yes, slightly. A worn tyre has a smaller diameter than a new one, so the speedometer reads slightly high as the tread wears — typically well under 1% over the life of the tyre. Under-inflation has the same direction of effect by reducing the effective rolling radius. Both are small compared with a size change, but they are real.