GPS Speedometer Calibration: GPS vs Speedometer Compared

For gps speedometer calibration, the point is this: GPS speed is the practical reference for checking a speedometer, because it measures the vehicle's actual movement over the ground rather than inferring speed from wheel revolutions. A speedometer calibrated for one tyre size reads wrong when the diameter changes; GPS does not care about the tyre size at all, which is why comparing the two reveals the error. This page explains how to make the comparison properly — steady speed, straight road, level ground — what GPS accuracy to expect, and how to turn the difference into the error percentage that the formula on this page uses, with a worked example using 205/55R16 and 215/55R16.

The comparison needs care: GPS speed is least reliable at low speed, while accelerating or braking, and on hills or in tunnels, so the reading should be taken at a steady speed on a straight, level stretch of road. Under those conditions a modern GPS receiver is typically accurate to within a small fraction of a mile per hour, which is good enough to measure a speedometer error of 1% or more. The worked example below uses a +1.74% tyre change — 205/55R16 (631.9 mm) to 215/55R16 (642.9 mm) — and the tables show the indicated-versus-actual speeds at 30, 50 and 70 mph. That is the point this page works through for gps speedometer calibration.

This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.

gps speedometer calibration: How the speedometer error is calculated

For gps speedometer calibration, the point is this: Two formulas cover everything on this page. Error % = (new diameter − old diameter) ÷ old diameter × 100, and actual speed = indicated speed × (new diameter ÷ old diameter). The diameters are the nominal new-tyre figures computed from the size codes — for example 205/55R16 measures 631.9 mm and 225/45R17 measures 634.3 mm — and real tyres vary slightly by brand, model, wear and inflation pressure, so the error figures are accurate to within a small margin rather than exact to the tenth of a percent. A positive error % means the new tyre is larger and the car travels faster than the dial shows; a negative error % means the new tyre is smaller and the car travels slower than the dial shows. The odometer error is the same percentage in the same direction.

What the speedometer actually measures for gps speedometer calibration

On this page, gps speedometer calibration is the case in point: A speedometer measures how fast the wheels are turning and converts that into a road speed using the rolling circumference of the tyres it was calibrated for. Change the tyre diameter and the conversion is wrong by exactly the percentage the diameter changed: a tyre 3% larger in diameter covers 3% more ground per revolution, so the car travels 3% faster than the dial shows, and the odometer records 3% fewer miles than the car actually covers. A tyre 3% smaller does the opposite. The error is proportional at every speed, which is why the tables in this article show the same percentage at 30, 50 and 70 mph, and why the formula below is all that is needed to work out the error for any size change.

Worked example: 205/55R16 to 215/55R16 for gps speedometer calibration

Taking gps speedometer calibration as the case in point: 205/55R16 measures 631.9 mm in overall diameter and 215/55R16 measures 642.9 mm. The error % is (642.9 − 631.9) ÷ 631.9 × 100 = +1.74%. At an indicated 30 mph the actual speed is 30 × (642.9 ÷ 631.9) = 30.5 mph; at 50 mph it is 50.9 mph; and at 70 mph it is 71.2 mph. The odometer is out by the same 1.74%: it records 98.29 miles for every 100 miles actually driven. The diameter change of 1.74% is inside the ±3% guideline commonly used for keeping speedometer error small, which is why this pair is a useful example — a larger change, such as 235/65R17 (737.3 mm) to 265/70R17 (802.8 mm), is +8.89% and gives 76.2 mph actual at an indicated 70 mph.

gps speedometer calibration: Indicated vs actual speed: the worked example

Error: +1.74%. Actual speed = indicated speed × (642.9 ÷ 631.9). That is the point this page works through for gps speedometer calibration.

Indicated speed Actual speed Difference
30 mph 30.5 mph +0.5 mph
50 mph 50.9 mph +0.9 mph
70 mph 71.2 mph +1.2 mph

For gps speedometer calibration, the point is this: The table is read from the indicated speed: find the dial reading and read across for the actual speed. The difference column is the amount by which the car is travelling faster than the dial shows, and it grows with speed because the error is a percentage. A 1.74% error is 0.5 mph at 30 mph and 1.2 mph at 70 mph — small in both cases, but the direction is the one that matters, because the car is going faster than the driver believes. Check the door-jamb placard for the specified size and confirm fitment with a tyre professional before fitting a different tyre size.

Common causes of a wrong speedometer for gps speedometer calibration

The causes divide into calibration and faults, and the distinction decides the fix. Calibration causes are tyre diameter changes, wear and inflation pressure: all of them change the distance covered per wheel revolution, and all of them produce a steady percentage error that the formulas on this page can predict. Fault causes are a failing wheel-speed sensor, a damaged reluctor ring, a worn speedometer cable on older vehicles, or a fault in the instrument cluster itself — these usually make the reading jump, stick or drop to zero rather than sit a steady percentage out. If the error is the same percentage at every speed, it is calibration; if it changes with speed or the needle behaves erratically, it is a fault and the vehicle needs diagnosis rather than a recalibration. That is the point this page works through for gps speedometer calibration.

gps speedometer calibration: How to fix a speedometer error

The fix is chosen by vehicle, not by preference. Modern vehicles with electronic speedometers are usually corrected by reprogramming the tyre-size setting with a diagnostic tool or a handheld programmer, which adjusts the speedometer and the odometer together. Older vehicles with a cable-driven speedometer need a different speedometer drive gear, and the new gear is selected using the diameter ratio — new teeth = old teeth × (old diameter ÷ new diameter) — so the gear compensates exactly for the size change. Where neither is available, an inline signal calibrator fitted to the speed sensor wiring can scale the reading. A dealer may be needed where the setting is locked behind manufacturer software. In every case, measure the error against GPS before and after the fix, at a steady speed on a straight road, to confirm the dial is right. That is the point this page works through for gps speedometer calibration.

gps speedometer calibration: Common mistakes with speedometer error

For gps speedometer calibration, the point is this: Mistakes usually start with the wrong reference. The first is comparing the dial with another vehicle's dial — both can be out by the same amount. GPS speed, measured at a steady speed on a straight road, is the practical reference, though it has its own limits at low speed and on hills. The second mistake is treating the error as a fixed mph figure: a 3% error is 0.9 mph at 30 mph and 2.1 mph at 70 mph, so a single-speed check does not describe the whole picture. The third is forgetting that most speedometers already read slightly high from the factory, so the error after a tyre change is measured from that baseline, not from zero. And the fourth is the dangerous one: fitting larger tyres makes the dial read low, so the car is going faster than the driver believes, and driving to the indicated limit in that condition means exceeding it.

gps speedometer calibration: Related pages

Frequently asked questions

How do I calculate speedometer error for gps speedometer calibration?

Use error % = (new diameter − old diameter) ÷ old diameter × 100, then actual speed = indicated speed × (new diameter ÷ old diameter). The worked example above uses 205/55R16 (631.9 mm) and 215/55R16 (642.9 mm), a +1.74% change, and the speedometer error calculator runs the same formula with your own sizes. That is the point this page works through for gps speedometer calibration.

How much can a speedometer be out?

For gps speedometer calibration, the point is this: It depends on the tyre change. A 1% diameter change is 0.7 mph at an indicated 70 mph; a 3% change is 2.1 mph; an 8.89% change, such as 235/65R17 to 265/70R17, is 6.2 mph at an indicated 70 mph. In the UK the law requires that a speedometer never under-reads and may over-read by up to 10% plus 4 km/h.

Why is my speedometer wrong after new tyres?

On this page, gps speedometer calibration is the case in point: The usual reason is a different diameter from the size the vehicle was calibrated for: a larger tyre makes the dial read low and a smaller tyre makes it read high, by the diameter percentage. Other causes are wear, pressure, a previous recalibration for a different size, or a sensor fault. Measure the error against GPS at a steady speed to find out which it is.

How do I check my speedometer against GPS?

On this page, gps speedometer calibration is the case in point: Drive at a steady speed on a straight, level road and compare the dial with a GPS speed reading. GPS is least reliable at low speed, while accelerating or braking, and on hills or in tunnels, so take the reading at a steady cruise. A difference that is the same percentage at several speeds is a calibration error; a needle that jumps or sticks is a fault.

Does tyre wear affect the speedometer?

Yes, slightly. A worn tyre has a smaller diameter than a new one, so the speedometer reads slightly high as the tread wears — typically well under 1% over the life of the tyre. Under-inflation has the same direction of effect by reducing the effective rolling radius. Both are small compared with a size change, but they are real. That is the point this page works through for gps speedometer calibration.