Gear Ratio Explained Simply: Explained Simply, With the Maths Shown and the Caveats Stated

There is a lot of confident advice about gear ratio explained simply and much of it is wrong in the details, usually because it leaves out the conditions the answer depends on. This page works through the question properly: what it is, why it matters, how to do or check it, and the mistakes that catch people out.

Below you will find the explanation, a worked example with the assumptions stated, a table where one helps, and the factors that push the result up or down. Read the whole page before you act, because the step that matters most is often the one people skip. That is the point this page works through for gear ratio explained simply.

What you need to know first — gear ratio explained simply

For gear ratio explained simply, the point is this: Gear ratios enter the same picture from the other side. A lower, numerically higher gear ratio multiplies the engine's torque and makes towing easier, at the cost of higher engine speed and more fuel use at cruising speed; a taller ratio does the opposite. Changing to bigger tyres has the same effect as fitting a taller ratio, because the tyre is effectively a bigger gear, and that is why drivers who fit bigger tyres often change the gear ratio to recover the lost performance. The maths is the RPM formula: RPM equals speed times gear ratio times final drive times 336, divided by the tyre diameter in inches.

What makes gear ratio explained simply worth understanding properly is that a small error at the start — a wrong figure, a skipped check — grows into a large error by the end, and the cost of that error is paid in tyres, fuel or safety.

How it works in practice — gear ratio explained simply

Taking gear ratio explained simply as the case in point: Towing capacity is not a single number printed on the car; it is the lowest of several limits, and the lowest one is the answer. The vehicle's tow rating, the tow bar's rating, the trailer's maximum weight and the combined weight limit for the car and trailer — the GCWR — all have to be respected, and the smallest of them decides how much can be towed. Exceeding any one of them is not a matter of the car struggling a little more; it is a matter of the brakes, the cooling, the suspension or the hitch being asked to do more than they were rated for.

Worked example — gear ratio explained simply

On this page, gear ratio explained simply is the case in point: Take a driver covering 16,000 miles a year as an example figure. The method on this page works the same at any mileage, so the example is there to show the arithmetic, not to state a fact about your car. Start with the measurement or the figure you can check yourself — a gauge reading, a tread-depth reading, or the figure on the placard — and write it down before you do anything else. Then apply the method step by step, checking each result against the one before it, because an error early in the chain is the one that is hardest to spot later. If the result surprises you, check the inputs first: a pressure read on warm tyres, a tread depth measured in one spot only, or a figure taken from the fitted tyre instead of the placard will each give a wrong answer that looks plausible. That is why the worked example on this page states its assumptions openly, and why you should do the same with your own figures.

What changes the answer — gear ratio explained simply

Taking gear ratio explained simply as the case in point: The figures that matter are found in the owner's manual, on the door-jamb sticker and on the VIN plate, and they vary by year, engine, axle ratio and towing package, so a figure quoted for a different version of the same model may not apply to your car. The only reliable figure is the one for your VIN. Tongue weight — the downward force the trailer puts on the tow ball — is usually 10 to 15 percent of the trailer's weight, and it counts against the car's payload, not just against the towing limit.

  • Vehicle tow rating: the maximum the manufacturer rates the vehicle to tow, found in the manual for your VIN. That is the point this page works through for gear ratio explained simply.
  • For gear ratio explained simply, the point is this: Tow bar rating: the tow bar itself has a limit, and it is often lower than the vehicle's rating.
  • GCWR: the maximum combined weight of the vehicle, the trailer and everything in both. That is the point this page works through for gear ratio explained simply.
  • On this page, gear ratio explained simply is the case in point: Payload: the tongue weight counts against payload, so a heavy trailer can use up the payload before the towing limit is reached.
  • For gear ratio explained simply, the point is this: Gear ratio: a numerically higher ratio gives more pulling torque for towing and for bigger tyres.
  • On this page, gear ratio explained simply is the case in point: Trailer weight distribution: how the load sits in the trailer decides the tongue weight and the stability.

Common mistakes — gear ratio explained simply

  • For gear ratio explained simply, the point is this: Quoting a tow rating for a different engine or package of the same model as if it applied to every version.
  • For gear ratio explained simply, the point is this: Forgetting that the tongue weight counts against the car's payload as well as the towing limit.
  • On this page, gear ratio explained simply is the case in point: Ignoring the GCWR and checking only the trailer weight against the tow rating.
  • For gear ratio explained simply, the point is this: Fitting bigger tyres without thinking about the gearing change, then wondering why towing feels harder.

Step by step — gear ratio explained simply

  1. On this page, gear ratio explained simply is the case in point: Find the tow rating, the GCWR and the payload for your exact vehicle in the owner's manual or on the door-jamb sticker.
  2. Find the tow bar's rating on the bar itself or in its paperwork. That is the point this page works through for gear ratio explained simply.
  3. Weigh the trailer fully loaded, or work out its weight from its plated maximum. That is the point this page works through for gear ratio explained simply.
  4. Check the tongue weight: it should be roughly 10 to 15 percent of the trailer's weight. That is the point this page works through for gear ratio explained simply.
  5. Take the lowest of the vehicle rating, the tow bar rating and the trailer limit as the maximum. That is the point this page works through for gear ratio explained simply.
  6. Taking gear ratio explained simply as the case in point: If the trailer is near the limit, reconsider the load, the gear ratio and the route before setting off.

What can go wrong, and when to see a professional — gear ratio explained simply

Most problems with gear ratio explained simply announce themselves early if you know what to look for: uneven wear, a vibration that was not there before, a warning light, a noise that changes with speed, or a reading that does not match the placard. None of these is a reason to panic, and all of them are reasons to check the basics first — pressures with a gauge when the tyres are cold, tread depth across the whole tread, and the figures on the placard rather than the ones on the fitted tyre. If the basics are right and the symptom is still there, or if you find a bulge, a deep cut, a cracked sidewall or a tyre that is losing pressure quickly, that is the point to see a tyre professional rather than to keep driving and hoping. A professional can see the inside of a tyre, measure the alignment angles and test the sensors, and those are the checks that cannot be done from the driveway. The cost of an inspection is small beside the cost of a tyre worn out early or a problem found too late.

Related guides — gear ratio explained simply

Frequently asked questions

Do gear ratios affect towing?

For gear ratio explained simply, yes. A numerically higher gear ratio multiplies engine torque and makes towing easier, at the cost of higher engine speed and fuel use when cruising. Fitting bigger tyres has the opposite effect, like fitting a taller gear, which is why drivers who fit bigger tyres often change the ratio to match.

How is towing capacity calculated?

For gear ratio explained simply, it is the lowest of the vehicle's tow rating, the tow bar's rating and the trailer's limit, and it must also respect the GCWR and the payload. The figures vary by year, engine, axle ratio and towing package, so confirm them for your VIN in the owner's manual or on the door-jamb sticker. Never exceed the lowest limit.

What is the difference between towing capacity and payload for gear ratio explained simply?

For gear ratio explained simply, towing capacity is the maximum weight the vehicle can pull behind it; payload is the maximum weight it can carry inside and on itself, including passengers, cargo and the tongue weight of the trailer. A trailer's tongue weight counts against payload, so a heavy trailer can use up the payload even when the towing limit is not reached.

What is GCWR?

For gear ratio explained simply, gCWR is the gross combined weight rating: the maximum allowed weight of the vehicle, the trailer and everything in both, added together. It is a separate limit from the towing capacity, and it can be the binding limit when the vehicle itself is heavily loaded.

How much tongue weight should a trailer have?

For gear ratio explained simply, roughly 10 to 15 percent of the trailer's loaded weight, pushing down on the tow ball. Too little tongue weight makes the trailer sway; too much overloads the rear of the car and uses up payload. Weigh the trailer and the tongue weight rather than guessing.