Gear Ratio Calculator Tyre Size: Worked Example With the RPM Formula

If you want a straight answer on gear ratio calculator tyre size, start with the formula: RPM equals speed times gear ratio times final drive times 336, divided by tyre diameter in inches. That one formula answers every gear-ratio question on this page — what RPM you will see at a given speed, what speed a given RPM means, and what ratio you need when the tyre size changes. This page works the formula step by step, gives RPM tables at 30, 50 and 70 mph, and explains what the numbers mean for acceleration, towing and cruising.

This is a calculation, not a safety approval. Always check your vehicle's door-jamb placard, load index and speed rating, and confirm fitment with a tyre professional before fitting a different tyre size.

gear ratio calculator tyre size: The RPM formula

Taking gear ratio calculator tyre size as the case in point: RPM = (speed × gear ratio × final drive × 336) ÷ tyre diameter (inches) is the whole method in one line. Speed is in mph, the gear ratio is the transmission gear in use — 1.00 in direct drive, under 1.00 in overdrive, 0.69 for a typical overdrive gear — the final drive is the axle ratio, and 336 is the constant that makes the units work. Turn it round for speed: speed = (RPM × tyre diameter) ÷ (gear ratio × final drive × 336). Diameters here are nominal (new-tyre) figures, and real tyres vary slightly by brand, model, wear and inflation pressure, so take the diameter from the tyre-size chart for your size: a 275/55R20 measures 810.5 mm (31.91 in) across.

gear ratio calculator tyre size: Worked example: RPM at 30, 50 and 70 mph

Take a 275/55R20 tyre with a nominal diameter of 810.5 mm (31.91 in) and a 3.55 axle ratio, in direct drive (gear ratio 1.00). At 70 mph, RPM = (70 × 1.00 × 3.55 × 336) ÷ 31.91 = 2,617. At 50 mph the same sum gives 1,869 RPM, and at 30 mph it gives 1,121 RPM. In overdrive — a 0.69 gear ratio, as an example — the 70 mph figure falls to 1,805 RPM, which is why motorway cruising feels relaxed in top gear. Change any one input and the answer moves in proportion: a bigger tyre lowers RPM, a higher ratio raises it, and a taller overdrive gear lowers it again. That is the point this page works through for gear ratio calculator tyre size.

RPM table: 30, 50 and 70 mph for gear ratio calculator tyre size

For gear ratio calculator tyre size, the point is this: RPM for a 3.55 axle ratio on a 275/55R20 tyre (31.91 in diameter). The direct-drive column uses a 1.00 gear ratio; the overdrive column uses 0.69 as an example.

Speed (mph) RPM in direct drive (1.00) RPM in overdrive (0.69)
30 1,121 774
50 1,869 1,290
70 2,617 1,805

gear ratio calculator tyre size: Speed at fixed RPM

Taking gear ratio calculator tyre size as the case in point: Rearranged, the formula gives speed from RPM. With the same 3.55 ratio and 31.91-inch tyre, 2,000 RPM in direct drive means 53.5 mph, and 3,000 RPM means 80.3 mph. In overdrive the same 2,000 RPM means 77.5 mph. That is the quickest way to sanity-check a ratio you have found on an axle tag: drive at a steady speed in a known gear, note the RPM, and see whether the formula's answer matches the speedometer. If it does not, either the ratio is not what you thought, the tyre diameter is not what you assumed, or the speedometer itself is off — all three are worth checking before spending money on gears.

What the gear ratio changes for gear ratio calculator tyre size

Think of the axle ratio as a torque multiplier. A numerically higher ratio — 4.10 instead of 3.21 — multiplies engine torque more before it reaches the wheels, so the vehicle pulls harder and tows more easily, but the engine spins faster at any road speed. A numerically lower ratio trades that pull for relaxed cruising and lower RPM on the motorway. Fuel use splits the same way in general terms: higher cruising RPM usually costs more fuel, while a ratio too low for the tyre size can also waste fuel, because the engine labours below its efficient range and the gearbox downshifts all the time. Bigger tyres act like a lower ratio, lowering RPM at a given speed, which is why a ratio change is the standard fix after fitting larger tyres. The right ratio is the one that keeps the engine in its useful rev range for the driving you actually do. That is the point this page works through for gear ratio calculator tyre size.

Common mistakes for gear ratio calculator tyre size

  • Using the rim size as the tyre diameter. A 17-inch rim is not a 17-inch tyre: the overall diameter includes both sidewalls, so a 265/70R17 is about 31.6 inches across, and using 17 inches in the formula gives nonsense. That is the point this page works through for gear ratio calculator tyre size.
  • Taking gear ratio calculator tyre size as the case in point: Forgetting the transmission gear. The formula needs the gear you are actually in: 1.00 in direct drive, less than 1.00 in overdrive. Using 1.00 for a top-gear cruise overstates the RPM by roughly a third.
  • For gear ratio calculator tyre size, the point is this: Ignoring the transmission's gear spacing. The axle ratio is only half the story: the transmission's own ratios decide how the gears step, and a wide-ratio gearbox can make a tall axle work where a close-ratio one would struggle.
  • For gear ratio calculator tyre size, the point is this: Treating the calculation as a safety approval. The formula tells you the RPM; it does not tell you the gears will fit, the axle will cope, or the vehicle is safe. Confirm fitment with a drivetrain specialist.

Related calculations for gear ratio calculator tyre size

These pages continue from here: the same method on a neighbouring question, or the calculator that runs the arithmetic for you. That is the point this page works through for gear ratio calculator tyre size.

Putting your figure to work for gear ratio calculator tyre size

Taking gear ratio calculator tyre size as the case in point: Putting the figure to work means using the formula with your own numbers before spending money. Measure the tyre diameter from the chart for your size, find the axle ratio from the tag or the build sheet, and work out the RPM at the speeds you actually drive. If the cruising RPM is far from where the engine is happy, a ratio change is worth pricing — but price the whole job, including the ring and pinion, the installation and the speedometer recalibration, and confirm the choice with a drivetrain specialist. The formula is the cheap part; the gears are the expensive part, and the calculation exists so you only buy them once.

Frequently asked questions

How accurate is the RPM formula?

It is exact for the inputs you give it: speed, gear ratio, final drive and tyre diameter. The uncertainty comes from the inputs, mainly the tyre diameter, which is a nominal new-tyre figure that varies slightly with brand, wear and pressure. A few percent either way is normal. That is the point this page works through for gear ratio calculator tyre size.

Does gear ratio affect fuel economy?

On this page, gear ratio calculator tyre size is the case in point: Yes, in both directions. A ratio that is too high raises cruising RPM and usually uses more fuel on the motorway; a ratio that is too low for the tyre size makes the engine labour and the transmission downshift, which can also waste fuel. The efficient ratio is the one that keeps the engine in its useful rev range for how you drive.

What does 3.73 mean on an axle tag?

For gear ratio calculator tyre size, the point is this: It means the driveshaft turns 3.73 times for one turn of the wheels. Higher numbers mean more torque multiplication and higher engine RPM at a given speed; lower numbers mean more relaxed cruising and less pull.

What is a gear ratio?

On this page, gear ratio calculator tyre size is the case in point: It is the number of times the driveshaft turns for one turn of the wheels. A 3.73 axle ratio means the driveshaft turns 3.73 times for each wheel revolution. A numerically higher ratio multiplies engine torque more and raises engine RPM at a given road speed.

What gear ratio do I need for bigger tyres?

On this page, gear ratio calculator tyre size is the case in point: Work out the ratio that restores the stock RPM: new ratio = old ratio × (new tyre diameter ÷ old tyre diameter). Pick the nearest common ratio as a starting point and confirm it with a drivetrain specialist, because transmission gearing and how the vehicle is used also matter.